Showing posts with label oscillator. Show all posts
Showing posts with label oscillator. Show all posts

Very Low Power 32kHz Oscillator

,
The 32-kHz low-power clock oscillator offers numerous advantages over conventional oscillator circuits based on a CMOS inverter. Such inverter circuits present problems, for example, supply currents fluctuate widely over a 3V to 6V supply range, while current consumption below 250 µA is difficult to attain. Also, operation can be unreliable with wide variations in the supply voltage and the inverter’s input characteristics are subject to wide tolerances and differences among manufacturers. The circuit shown here solves the above problems. Drawing just 13 µA from a 3V supply, it consists of a one-transistor amplifier/oscillator (T1) and a low-power comparator/reference device (IC1).

Very Low Power 32kHz OscillatorThe base of T1 is biased at 1.25 V using R5/R4 and the reference in IC1. T1 may be any small-signal transistor with a decent beta of 100 or so at 5µA (defined here by R3, fixing the collector voltage at about 1 V below Vcc). The amplifier’s nominal gain is approximately 2 V/V. The quartz crystal combined with load capacitors C1 and C3 forms a feedback path around T1, whose 180 degrees of phase shift causes the oscillation. The bias voltage of 1.25 V for the comparator inside the MAX931 is defined by the reference via R2. The comparator’s input swing is thus accurately centered around the reference voltage.

Operating at 3 V and 32 kHz, IC1 draws just 7 µA. The comparator output can source and sink 40mA and 5mA respectively, which is ample for most low-power loads. However, the moderate rise/fall times of 500 ns and 100 ns respectively can cause standard, high-speed CMOS logic to draw higher than usual switching currents. The optional 74HC14 Schmitt trigger shown at the circuit output can handle the comparator’s rise/fall times with only a small penalty in supply current.
Read more →

1 800 Oscillator

,
Oscillators are ten a penny, but this one has something special. Its frequency can be adjusted over a range of 800:1, it is voltage controlled, and it switches off automatically if the control voltage is less than approximately 0.6 V. As can be seen from the chart, the characteristic curve f = f(Ue) is approximately logarithmic. If the input voltage is less than 0.7 V, T1 and T3 are cut off. The capacitor then charges via the 10-kW resistor. The combination of the capacitor, the two Schmitt triggers and T2 form the actual oscillator circuit. However, T2 cannot discharge the capacitor, because T3 is cut off.


In this state, a low level is present at A1 and a high level is present at A2. If the input voltage is increased, T3 starts conducting. This allows the capacitor to be discharged via T2, and the circuit starts to oscillate. If Ue is further increased, the capacitor receives an additional charging current via T1 and the l00-Ω resistor. That causes the oscillator frequency to increase. In situations where the duty cycle of the output signal is not important (such as when the circuit is used as a clock generator), this circuit can be used as a voltage-controlled oscillator (VCO) with a large frequency range and shutdown capability. 
Read more →

Simple Oscillator Pipe Locator

,
Sometimes the need arises to construct a really simple oscillator. This could hardly be simpler than the circuit shown here, which uses just three components, and offers five separate octaves, beginning around Middle C (Stage 14). Octave # 5 is missing, due to the famous (or infamous) missing Stage 11 of the 4060B IC. We might call this a Colpitts ‘L’ oscillator, without the ‘C’. Due to the reactance of the 100-µH inductor and the propagation delay of the internal oscillator, oscillation is set up around 5 MHz. When this is divided down, Stage 14 approaches the frequency of Middle C (Middle C = 261.626 Hz). Stages 13, 12, 10, and 9 provide higher octaves, with Stages 8 to 4 being in the region of ultrasound.

Simple Oscillator/Pipe Locator Circuit Diagram

Simple Oscillator-Pipe Locator-Circuit Diagram

If the oscillator’s output is taken to the aerial of a Medium Wave Radio, L1 may serve as the search coil of a Pipe Locator, with a range of about 50 mm. This is tuned by finding a suitable hetero-dyne (beat note) on the medium wave band. In that case, piezo sounder Bz1 is omitted. The Simple Oscillator / Pipe Locator draws around 7 mA from a 9-12 V DC source.


Source:  http://www.ecircuitslab.com/2012/05/simple-oscillator-pipe-locator.html
Read more →