The circuit has been designed to produce a battery charger for automobiles that are using 12V batteries only. BTY79 is a 10A Silicon controlled rectifier with an operational temperature range from 0ºC to 125ºC. C106D is a 4A sensitive gate Silicon controlled rectifier that functions as reverse blocking thyristors designed for high volume consumer applications such as light, speed control, temperature, process and remote control, and warning systems where reliability of operation is important.
The typical car battery chargers have simple designs that produce a few amperes during its operation while charging the battery continuously. In the event that the charger is not turned OFF, overcharging will occur with due to evaporation which looses electrolyte and might cause damage to its elements. With the design of this circuit, this type of problem can be avoided by monitoring the condition of charging of the battery via the retroactive control circuit.
This is done by imposing a high current charge until the charging is complete. The LED LD2 will indicate that charging is full which will eventually deactivate the charging circuit. In creating this design, the cables that connect the transformer to the circuit should have enough cross-sectional area to prevent voltage drop when heat is produced as the current flows through. The adjustment of the circuit comes after the design, with the adjustment of TR1 to null value.
The LEDs are checked without connecting the battery initially and allowing them to turn ON. By connecting a battery, a 2A to 4A current is permitted to flow while ensuring that LD2 is turned OFF. TR1 is carefully adjusted to a few hundred milliamps until LD2 turns ON. This is done using the hydrometer technique. The correct adjustment allows LD2 to begin flickering as the battery is being charged. Connected to the battery is Q1, since it functions as a rectifier and charges the battery, which can be fired in each half cycle by R3-4 and LD2.
In case an uncharged battery is connected, a low terminal voltage is obtained. When the voltage of the battery exceeds the predetermined value, Q2 is activated by the combination of C1, TR1, R2, and D2. Q1 is deactivated with the current supply cut off as the battery terminal voltage is increased where Q2 shifts the control of Q1 gate after TR1 fixed the increased battery terminal voltage above the level. A heat sink should be mounted on the bridge rectifier GR1 and Q1 to prevent overheating. A 5A DC ammeter M1, connected in parallel, is used to measure the charge current.
The circuit’s theory of design will only be applied to batteries with rating of 12V. These batteries are mainly used in a variety of vehicles used in land, air, and water such as personal watercraft like boat, yacht, Jet Skis, and other marine applications. They are also utilized widely in automobiles and motorcycles such as quad bike, RVs, snowmobile, motor scooter, utility vehicle, and riding mower. It can also be beneficial to disabled persons by providing aid to wheelchairs and mobility scooters.
R1= 1Kohms
R2= 1.2Kohms
R3= 470 ohms
R4= 470 ohms
R5= 10Kohms
C1= 10uF 25V
D1= 1N4001
D2= 6.8V 0.5W zener
TR1= 4.7Kohms trimmer
Q1= BTY79 or similar 6A SCR
Q2= C106D SCR
GR1= 50V 6A Bridge Rectifier
T1= 220V/17V 4A Transformer
LD1= Green LED
LD2= Red LED
M1= 0-5A DC Ampere meter
S1= 10A D/P On Off Switch
F= 5A Fuse
Read more →
Circuit Diagram:
 |
| DC 12V - Car Battery Charger Circuit Diagram |
The typical car battery chargers have simple designs that produce a few amperes during its operation while charging the battery continuously. In the event that the charger is not turned OFF, overcharging will occur with due to evaporation which looses electrolyte and might cause damage to its elements. With the design of this circuit, this type of problem can be avoided by monitoring the condition of charging of the battery via the retroactive control circuit.
This is done by imposing a high current charge until the charging is complete. The LED LD2 will indicate that charging is full which will eventually deactivate the charging circuit. In creating this design, the cables that connect the transformer to the circuit should have enough cross-sectional area to prevent voltage drop when heat is produced as the current flows through. The adjustment of the circuit comes after the design, with the adjustment of TR1 to null value.
The LEDs are checked without connecting the battery initially and allowing them to turn ON. By connecting a battery, a 2A to 4A current is permitted to flow while ensuring that LD2 is turned OFF. TR1 is carefully adjusted to a few hundred milliamps until LD2 turns ON. This is done using the hydrometer technique. The correct adjustment allows LD2 to begin flickering as the battery is being charged. Connected to the battery is Q1, since it functions as a rectifier and charges the battery, which can be fired in each half cycle by R3-4 and LD2.
In case an uncharged battery is connected, a low terminal voltage is obtained. When the voltage of the battery exceeds the predetermined value, Q2 is activated by the combination of C1, TR1, R2, and D2. Q1 is deactivated with the current supply cut off as the battery terminal voltage is increased where Q2 shifts the control of Q1 gate after TR1 fixed the increased battery terminal voltage above the level. A heat sink should be mounted on the bridge rectifier GR1 and Q1 to prevent overheating. A 5A DC ammeter M1, connected in parallel, is used to measure the charge current.
The circuit’s theory of design will only be applied to batteries with rating of 12V. These batteries are mainly used in a variety of vehicles used in land, air, and water such as personal watercraft like boat, yacht, Jet Skis, and other marine applications. They are also utilized widely in automobiles and motorcycles such as quad bike, RVs, snowmobile, motor scooter, utility vehicle, and riding mower. It can also be beneficial to disabled persons by providing aid to wheelchairs and mobility scooters.
Parts:
R1= 1Kohms
R2= 1.2Kohms
R3= 470 ohms
R4= 470 ohms
R5= 10Kohms
C1= 10uF 25V
D1= 1N4001
D2= 6.8V 0.5W zener
TR1= 4.7Kohms trimmer
Q1= BTY79 or similar 6A SCR
Q2= C106D SCR
GR1= 50V 6A Bridge Rectifier
T1= 220V/17V 4A Transformer
LD1= Green LED
LD2= Red LED
M1= 0-5A DC Ampere meter
S1= 10A D/P On Off Switch
F= 5A Fuse
