Showing posts with label audio. Show all posts
Showing posts with label audio. Show all posts

Condenser Mic Audio Amplifier Circuit Diagram

,

The compact, low-cost condenser mic audio amplifier described here provides good-quality audio of 0.5 watts at 4.5 volts. It can be used as part of intercoms, walkie-talkies, low-power transmitters, and packet radio receivers. Transistors T1 and T2 form the mic preamplifier. Resistor R1 provides the necessary bias for the condenser mic while preset VR1 functions as gain control for varying its gain. In order to increase the audio power, the low-level audio output from the preamplifier stage is coupled via coupling capacitor C7 to the audio power amplifier built around BEL1895 IC.BEL1895 is a monolithic audio power amplifier IC designed specifically for sensitive AM radio applications that delivers 1 watt into 4 ohms at 6V power supply voltage. It exhibits low distortion and noise and operates over 3V-9V supply voltage, which makes it ideal for battery operation. A turn-on pop reduction circuit prevents thud when the power supply is switched on. Coupling capacitor C7 determines low-frequency response of the amplifier. Capacitor C9 acts as the ripple-rejection filter.

Circuit Diagram :

Condenser Mic Audio Amplifier Circuit Diagram

Condenser Mic Audio Amplifier Circuit Diagram


Capacitor C13 couples the output available at pin 1 to the loudspeaker. R15-C13 combination acts as the damping circuit for output oscillations. Capacitor C12 provides the boot strapping function. This circuit is suitable for low-power HAM radio transmitters to supply the necessary audio power for modulation. With simple modifications it can also be used in intercom circuits.

Author: D. Prabakaran - Copyright: Electronics For You Mag

Read more →

1W BTL Audio Amplifier circuit and explanation

,
The TDA8581(T) from Philips Semiconductors is a 1-watt Bridge Tied Load (BTL) audio power amplifier capable of delivering 1 watt output power into an 8-Wload at THD (total harmonic distortion) of 10% and using a 5V power supply. The schematic shown here combines the functional diagram of the TDA8551 with its typical application circuit. The gain of the amplifier can be set by the digital volume control input. At the highest volume setting, the gain is 20 dB. Using the MODE pin the device can be switched to one of three modes: standby (MODE level between Vp and Vp–0.5 V), muted (MODE level between 1 V and Vp–1.4 V) or normal (MODE level less than 0.5 V). The TDA8551 is protected by an internal thermal shutdown protection mechanism. The total voltage loss for both MOS transistors in the complementary output stage is less than 1 V.

Circuit diagram:1-Watt BTL audio amplifier
1 Watt BTL Audio Amplifier Circuit Diagram

Using a 5-V supply and an 8-W loudspeaker, an output power of 1 watt can be delivered. The volume control has an attenuation range of between 0 dB and 80 dB in 64 steps set by the 3-state level at the UP/DOWN pin: floating: volume remains unchanged; negative pulses: decrease volume; positive pulses: increase volume Each pulse at he Up/DOWN pin causes a change in gain of 80/64 = 1.25 dB (typical value). When the supply voltage is first connected, the attenuator is set to 40 dB (low volume), so the gain of the total amplifier is then –20 dB. Some positive pulses have to be applied to the UP/DOWN pin to achieve listening volume. The graph shows the THD as a function of output power. The maximum quiescent current consumption of the amplifier is specified at 10 mA, to which should be added the current resulting from the output offset voltage divided by the load impedance.
Read more →

Audio Amplifier Kitsaudio Amplifier Brandmodel Number Tomcatso

,
Vehicle Wiring Products on Car Power Seats Control Wire Harness   Dongguan Yacenter Electric Co
Car Power Seats Control Wire Harness Dongguan Yacenter Electric Co.


Vehicle Wiring Products on Car Audio Wire For Sale Buy Cheap Rock Power Car Audio Wire Products
Car Audio Wire For Sale Buy Cheap Rock Power Car Audio Wire Products.


Vehicle Wiring Products on Relay Wiring Diagram 8 Pin  Relay Wiring Diagram 8 Pin Manufacturers
Relay Wiring Diagram 8 Pin Relay Wiring Diagram 8 Pin Manufacturers.


Vehicle Wiring Products on Used For Engine Of Car Wiring Harness  Used For Engine Of Car Wiring
Used For Engine Of Car Wiring Harness Used For Engine Of Car Wiring.


Vehicle Wiring Products on Audio Amplifier Kits  Audio Amplifier Brand  Model Number In Tomcatso
Audio Amplifier Kits Audio Amplifier Brand Model Number In Tomcatso.


Vehicle Wiring Products on Automotive Wire Harness
Automotive Wire Harness.


Vehicle Wiring Products on Vwp   Brake Pipes   Fittings
Vwp Brake Pipes Fittings.


Vehicle Wiring Products on Car Amplifier Repair  Car Amplifier Brand  Model Number In Tomcatso
Car Amplifier Repair Car Amplifier Brand Model Number In Tomcatso.


Vehicle Wiring Products on Voltage Automotive Wire   China Thin Wall Low Voltage Automotive Wire
Voltage Automotive Wire China Thin Wall Low Voltage Automotive Wire.


Vehicle Wiring Products on Trac Vehicle Wiring Kit   Trac Outdoor Products T10135   Iboats
Trac Vehicle Wiring Kit Trac Outdoor Products T10135 Iboats.


Read more →

10 Watts Mosfet Audio Amplifier

,
10 Watts Mosfet Audio Amplifier

The diagram shown here is a MOSFET amplifier circuit 10W of sound that only requires a single source. Single railway material rarely used in power amplifiers class-B. However, for low power applications like this is very thin. Actually I have this circuit a old cassette player is still working and republish as it is. The BD512 and BD522 power MOSFETs is obsolete now and you can use any other power MOSFET game instead of them.



Transistors Q1 and Q2 are connected as a Darlington pair works as a preamp. R3 preset controls the quiescent current, while R2 provides. Output is coupled to the speakers through capacitor C4. Capacitor C5 is the power supply filter and C2 is the input DC decoupling capacitor.



Notes.

  • The circuit can be assembled on a vero board.
  • Use 30V DC for powering the circuit.
  • Do not expect much performance from this amplifier.
  • Capacitors C3, C4, C5 must be rated 50V and C2 can be 10V.
  • Use a 8 ohm 15W speaker as load.
Read more →

25W Audio Power Amplifier Rise

,
This audio power amplifier project is based on LM1875 amplifier module from National Semiconductor. It can deliver up to 30W of power using an 8 ohm load & dual 30V DC power supplies. It is designed to operate with maximum outside parts with current limit & thermal shutdown protection features . Other features include high gain, quick slew rate, wide power supply range, giant output voltage swing & high current capability.

Summary of the audio amply-fire features:

  • Low distortion: 0.015%, 1 kHz, 20 W
  • Wide power bandwidth: 70 kHz
  • Wide supply range 16V-60V
  • Up to 30 watts output power
  • Internal output protection diodes
  • Protection for AC & DC short circuits to ground
  • 94 dB ripple rejection
  • Plastic power package TO-220
25V Power Supply

The schematic below shows how the +25V DC & -25V DC are obtained. In order to provide power supply for two stereo amplifiers, a power transformer rating of 80VA with 240V/36V middle tapped secondary winding is used. The secondary output of the transformer is rectified by using 1N5401 diodes together with four electrolytic capacitors to smoother the ripple voltage. A fuse & a varistor are connected at the primary input to protect the circuit against power surge.



Audio Amplifier Module

The +25V & -25V DC power supply are connected to the audio amplifier module through a 2A fuse with the peripheral devices shown in the schematic below. The audio input signal to be amplified is coupled to pin one of LM1875 through the resistor R1 and electrolytic capacitor E5.

The output signal at pin four of LM1875 can be used to directly drive a 8 ohm loudspeaker. Resistor R6 and capacitor C5 prevent-the capacitance developed at the long speaker leads from driving the amplifier in to High Frequency Oscillation.

A heat-sink with a thermal resistance rating of one.4 Cecilius/Watt or better must be used or else the amplifier module will-be cut-off from operation due to the heat that will build up in the coursework of the operation of the amplifier. Take note that the heat sink tab on the IC module is internally connected to the -25V power supply hence it must be isolated from the heat sink by the use of an insulating washer. If this is not done, the negative rail will be shorted to ground.





Read more →

Symmetric Output for USB Audio DAC

,
This simple adapter circuit is specially intended for use with the USB Audio DAC published in this website elsewhere. With an easily implemented modification, it is possible to make the output of the D/A converter pseudo-symmetric, so that it can be connected to professional equipment having XLR line inputs. This will do even more justice to the high quality of the USB Audio DAC. The modification actually amounts to just adding a single resistor (R11a) and changing the value of the existing resistor at the output of the audio DAC (R11) from 100 Ωto 68Ω. Components C14 and R12 remain unchanged. It is not difficult to make this change on the printed circuit board of the audio DAC, but a bit of improvisation is necessary. After replacing R11 with a 68-Ω version, unsolder R12 and connect R11a in series with it. Bring out the junction of these two resistors to act as the signal return connection (pin 3 of the XLR socket). The same operation must also be carried out on the right channel, where the affected resistors are labelled R16, R16a and R17.

Symmetric Output for USB Audio DAC circuit diagram
Read more →

6 18 Volt audio power amplifier

,
audio power amplifier circuit
This time I will post about the audio amplifier based on IC KA2204. In an audio amplifier circuit has a power output that can also be referred to as a low-grade resources that have only 6 Watts output with 4 Ohm impedance. Frequency response 30 Hz to 18 kHz . For the scheme can be seen below.





Supply voltage and a maximum of at least 6 Volt to 18 Volt
Supply voltage and a maximum of at least 6 Volt to 18 Volt

Part List
R1 =  56R
C1 = 1uF
C2 = 220uF
C3 = 100uF
C4 = 47uF
C5 = 1000uF
C6 = 100nF
C7 = 470pF
C8 = 22pF
C9 = 47uF
C10 = 47pF



Read more →

AUDIO LEVEL METER ELECTRONIC DIAGRAM

,

AUDIO LEVEL METER ELECTRONIC DIAGRAM

It consists of only few components. IC LM3915 converts the audio analog voltage and display it to the LED. Here is the schematic :

Parts list :


  •     Resistor R1 : 1k2
  •     Resistor variable R2 : 10k
  •     IC : LM3915
  •     LED indicator LED1-LED10 : LED 5mm
  •     12V power supply


Read more →

2 3 Watt Low audio power amplifier

,
KA2202 , KA2207
These amplifiers using IC KA2202 and KA2207, which has a power output of 2.3 Watt berimpedansi 4 ohms. Minimum supply voltage and maximum 5Volt 20Volt. See schematics and component list below.



Part List 
R1 = 100K
R2 = 56R
R3 = 56R
R4 = 1R
Use 1/4 Watt resistor
10W schematic amplifier with KA2202 , KA2207

C1 = 100uF
C2 = 100uF
C4 = 100uF
C5 = 470uF
C6 = 100nF
C7 = 470pF
C8 = 2,2nF
C9 = 100uF
U1 = KA2202 , KA2207
Read more →

Audio Indicator Circuit Diagram Using LM741

,

This circuit can be used to remotely monitor a loudspeaker, alarm, or audio source for presence of an audio waveform. It can also be directly connected across loudspeaker terminals used as a peak indicator. If you need to monitor some audio signal at a location that is either soundproof are too far away to actually hear the signal then you can use a circuit similar to this one.

Circuit Diagram:

Audio Indicator Circuit Diagram Using LM741 Audio Indicator Circuit Diagram Using LM741

A remote indication that the audio source is active is provided visually, here in the form of a LED. Referring to the above circuit, the 10k preset is a level control which should be adjusted so that when the source ( audio signal or alarm ) is producing the desired amount of noise, the LED lights. The input stage is an inverting x100 amplifier made with a 741 op-amp.

Author: Andy Collinson

Read more →

USB Powered Audio Power Amplifier

,
This circuit of multimedia speakers for PCs has single-chip-based design, low-voltage power supply, compatibility with USB power, easy heat-sinking, low cost, high flexibility and wide temperature tolerance. At the heart of the circuit is IC TDA2822M. This IC is, in fact, mono-lithic type in 8-lead mini DIP package. It is intended for use as a dual audio power amplifier in battery-powered sound players. Specifications of TDA2822M are low quiescent current, low crossover distortion, supply voltage down to 1.8 volts and minimum output power of around 450 mW/channel with 4-ohm loudspeaker at 5V DC supply input.

An ideal power amplifier can be simply defined as a circuit that can deliver audio power into external loads without generating significant signal distortion and without consuming excessive quiescent current. This circuit is powered by 5V DC supply available from the USB port of the PC. When power switch S1 is flipped to ‘on’ position, 5V power supply is extended to the circuit and power-indicator red LED1 lights up instantly. Resistor R1 is a current surge limiter and capacitors C1 and C4 act as buffers. Working of the circuit is simple. Audio signals from the PC audio socket/headphone socket are fed to the amplifier circuit through components R2 and C2 (left channel), and R3 and C3 (right channel)

USB Powered Audio Power Amplifier Circuit diagram:

USB Powered Audio Power Amplifier Circuit Diagram

Potmeter VR1 works as the volume controller for left (L) channel and potmeter VR2 works for right (R) channel. Pin 7 of TDA2822M receives the left-channel sound signals and pin 6 receives the right-channel signals through VR1 and VR2, respectively. Ampl i f ied signals for driving the left and right loudspeakers are available at pins 1 and 3 of IC1, respectively. Components R5 and C8, and R6 and C10 form the traditional zobel network. Assemble the circuit on a medium-size, general-purpose PCB and enclose in a suitable cabinet. It is advisable to use a socket for IC TDA2822M. The external connections should be made using suitably screened wires for better result.
Sucre:  http://www.ecircuitslab.com/2011/06/usb-powered-audio-power-amplifier.html
Read more →

Dual 20 Watt Audio Power Amplifier

,

Overture Audio Power Amplifier Series Dual 20-Watt Audio Power Amplifier with Mute and Standby Modes

The LM1876 is a stereo audio amplifier capable of delivering typically 20W per channel of continuous average output power into a 4 or 8 load with less than 0.1% THD+N.

Each amplifier has an independent smooth transition fade-in/out mute and a power conserving standby mode which can be controlled by external logic.

The performance of the LM1876, utilizing its Self Peak Instantaneous Temperature (°Ke) (SPiKe™) protection circuitry, places it in a class above discrete and hybrid amplifiers by providing an inherently, dynamically protected Safe Operating Area (SOA). SPiKe protection means that these parts are safeguarded at the output against overvoltage, undervoltage, overloads, including thermal runaway and instantaneous temperature peaks.

Circuit Diagram

Dual 20-Watt Audio Power Amplifier Dual 20-Watt Audio Power Amplifier Circuit Diagram

Key Specification
THD+N at 1kHz at 2 x 15W continuous average
output power into 4 or 8: 0.1% (max)
THD+N at 1kHz at continuous average
output power of 2 x 20W into 8: 0.009% (typ)
Standby current: 4.2mA (typ)

Applications

  • High-end stereo TVs
  • Component stereo
  • Compact stereo

    Features

  • SPiKe protection
  • Minimal amount of external components necessary
  • Quiet fade-in/out mute mode
  • Standby-mode
  • Isolated 15-lead TO-220 package
  • Non-Isolated 15-lead TO-220 package
  • Wide supply range 20V - 64V

  • Read more →